Source

 

 

What are your ideas about Tools You Need to Install a New Bathtub ?

Setting up a bathtub isn't specifically brain surgery, however it does require solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is also a reasonably tough project. If the old bathtub is conveniently easily accessible, the project can relocate rapidly; if you have to open up a wall surface to remove the old bathtub and also position the brand-new bath tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will require an assistant to move out the old bathtub as well as set in the new one. Make sure you have actually qualified on your own for the job as well as are comfortable attempting it. Rather than employing a contractor to take control of a halfway-completed project, it is much better to take into consideration utilizing one prior to you begin. Chances are you might need a professional plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your bathroom if you have actually already acquired a new tub and also don't require to alter the arrangement of your previous water system pipes.
Your devices as well as material list ought to consist of the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Removing Old Taps

If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the supply of water. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted accessibility that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the installing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Secure the tap in place with the maker given backnut. As soon as the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former type ought to be linked to the tap finishes initially, tightening up just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

 

 

Mounting the Bathtub

Utilizing the two wooden boards under its feet, put the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the level and also readjusting the feet on the bath tub up until the level checks out level.
To install taps, fit the bottom of the outermost adaptable faucet port to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the supply of water and check all joints and also brand-new pipework for leakages as well as tighten them if necessary. Fill the bath tub as well as likewise check the overflow outlet and also the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bathtub should wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its final setting.

 

 

Preparing for the Setup

Firstly, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap includes a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to avoid strain on the tub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its final setting.

 

 

Tiling Around the Tub

In the location where the bath satisfies the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, creating the water to penetrate the wall in between the bathroom and also the tiling, leading to problems with moisture and also feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is advisable to fit the tiles making use of waterproof or water-proof glue and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you really like reading about How to Install a Bathtub Yourself? Write a remark down the page. We will be glad to listen to your opinion about this piece. Hoping that you come back again in the future. Those who liked our post plz make sure you remember to pass it around. Thanks for taking the time to read it.

Booking